Browse "Dept. of Mechanical Engineering(기계공학과)" by Type Thesis(Master)

Showing results 595 to 614 of 3882

595
Gas metal arc welding 의 자동화를 위한 최적 용접 조건에 관한 연구 = A study on optimal welding parameters for the automation of gas metal arc weldinglink

이종희; Lee, Jong-Hee; et al, 한국과학기술원, 1986

596
Generation of subject-specific motions at various walking speeds using meta reinforcement learning and generative adversarial networks = 메타 강화학습과 생성적 적대 신경망을 이용한 특정인의 다양한 속도 보행 동작 생성link

Jung, Mingi; Koo, Seungbum; et al, 한국과학기술원, 2022

597
Geometrical adaptive control of machining straightness in end milling = 엔드 밀링 작업에서의 진직도 개선을 위한 기하학적 적응 제어link

Kim, Jong-Sun; 김종선; et al, 한국과학기술원, 1985

598
Geometry independent planar manipulation by multiple cooperating mobile robots = 군집협업로봇에 의한 기하 독립체의 평면이동link

Sankar, Hari; Kim, Soo-hyun; et al, 한국과학기술원, 2009

599
GERT 를 이용한 재공품 관리 = Work-in-process control using GERTlink

신현기; Shin, Hyun-Ki; et al, 한국과학기술원, 1980

600
GHP 실외기 설계 인자에 따른 3차원 내부 유동 특성 고찰 = Analysis of three-dimensional flow about the outdoor unit of a gas-engine driven heat pump systemlink

정유라; Chung, Yu-La; et al, 한국과학기술원, 2004

601
GMA 용접공정의 용접선 추적에 대한 아크빛의 적용 = Application of light emission to seam tracking in GMAW processlink

이현수; Lee, Hyun-Soo; et al, 한국과학기술원, 1994

602
GMA 용접에서 단락이행 모드의 품질평가 방법에 관한 연구 = Study on weld quality assessment method of short-circuit Gas Metal Arc weldinglink

김재민; Kim, Jae-Min; 나석주; 유중돈; et al, 한국과학기술원, 2001

603
GMA 용접용 토치의 형상에 따른 분위기 가스조성과 용접 품질에 미치는 영향 = Effects of GMAW torch configurations on shielding gas composition and weld quality GMAlink

문명철; Moon, Myung-Chul; et al, 한국과학기술원, 1999

604
GMAW 공정에서 아크 안정성의 실시간 측정 = Real-time estimation of arc stability in gas metal arc welding processeslink

강성택; Kang, Sung-Taek; et al, 한국과학기술원, 1989

605
GMAW 공정에서의 용접선 자동추적에 관한 연구 = A study on the seam tracking of the GMAW processlink

최한호; Choi, Han-Ho; et al, 한국과학기술원, 1990

606
GMAW 공정의 아크 길이 변화에 따른 아크 빛에 관한 연구 = A study on arc light intensity due to arc length change in GMAWlink

유용상; Yoo, Yong-Sang; et al, 한국과학기술원, 1996

607
GMAW 용접공정에서 온도분포의 동적 거동에 관한 연구 = An analysis of temperature distribution in GMAW welding processlink

이재우; Lee, Jae-Woo; et al, 한국과학기술원, 1988

608
GMT 평판의 bolted joint 강도에 관한 연구 = A study on bolted joint strength of GMT platelink

강완석; Kang, Wan-Seok; et al, 한국과학기술원, 2002

609
GPS수신기와 dead reckoning센서를 결합한 위치 결정에 관한 연구 = A study on the position location by integration of GPS receiver and dead reckoning sensorslink

노재선; Noh, Jae-Seon; et al, 한국과학기술원, 1996

610
Grasshopper 링크 기구를 이용한 가솔린 기관의 피스톤-링 결합체의 측정에 관한 실험적 연구 = An experimental study on friction measurement of piston-ring assembly of a SI engine utilizing grasshopper linkage systemlink

서승우; Seo, Sung-Woo; et al, 한국과학기술원, 1989

611
GRIN probe를 이용한 광섬유 번들 공초점 내시경의 설계 및 광효율 향상에 관한 연구 = A study on improvement of efficiency to enhance the contrast for confocal microendoscope with GRIN.link

안진우; Ahn, Jin-Woo; et al, 한국과학기술원, 2008

612
GTA 용접에 있어서 천이과정 온도분포의 3차원 해석에 관한 연구 = A study on the 3-dimensional analysis of the transient temperature distribution in GTAWlink

이승영; Lee, Seung-Young; et al, 한국과학기술원, 1986

613
GTAW를 이용한 파이프 내부 원주 용접의 공정해석에 관한 연구 = A study on process analysis in pipe inside girth welding using GTAWlink

조영태; Cho, Young-Tae; et al, 한국과학기술원, 1999

614
Gyromill 풍차의 효율해석과 모델 연구 = Analysis of the performance of gyromill-rotor and model studylink

김희식; Kim, Hee-Sik; et al, 한국과학기술원, 1979

rss_1.0 rss_2.0 atom_1.0